# ESP32 Device Framework

A reusable ESP32 firmware base with Wi-Fi, web configuration UI, authentication, MQTT / Home Assistant integration, and factory reset. Add device-specific logic on top without re-implementing the boilerplate.

## Table of contents

- [Features](#features)
- [Building and flashing](#building-and-flashing)
- [First-time Wi-Fi setup](#first-time-wi-fi-setup)
- [Web UI](#web-ui)
- [MQTT / Home Assistant](#mqtt--home-assistant)
- [HTTP API](#http-api)
- [Configuration reference](#configuration-reference)
- [Extending the framework](#extending-the-framework)

---

## Features

- **Wi-Fi** via WiFiManager — captive-portal setup on first boot, credentials stored in flash
- **mDNS** — device reachable as `<hostname>.local`
- **Web UI** — responsive configuration page served from the device, with logo support
- **Authentication** — optional HTTP Basic Auth to protect the web UI
- **MQTT** — connects to any broker, publishes an availability topic, reconnects automatically without blocking the web server
- **Home Assistant discovery** — stub ready for your entities
- **Factory reset** — rapid power-cycling clears settings (5× config, 10× config + Wi-Fi credentials)
- **Config persistence** — all settings stored as JSON in LittleFS (`/config.json`)

---

## Building and flashing

The project uses [PlatformIO](https://platformio.org/).

```bash
# Build
pio run -e esp32dev

# Flash firmware
pio run -e esp32dev --target upload

# Upload filesystem image (logo, etc.) — only needed when data/ changes
pio run -e esp32dev --target uploadfs

# Open serial monitor (115 200 baud)
pio device monitor
```

> **Note:** close the serial monitor before uploading — it holds the serial port exclusively.

Board targets: `esp32dev`, `esp32-s3-devkitc-1`

---

## First-time Wi-Fi setup

On first boot (or when stored Wi-Fi credentials are missing), the device starts an access point named **ESP32-Device**. Connect to it with any phone or laptop — a captive portal will appear automatically.

1. Enter your Wi-Fi SSID and password.
2. Optionally change the **Device hostname** (default: `esp32-device`, max 63 characters).
3. Click **Save**. The device connects to your network and restarts.

After connecting, the device is reachable at:

- `http://<hostname>.local` (default `http://esp32-device.local`) — mDNS, works on most local networks
- `http://<IP address>` — shown in the serial monitor on boot

### Factory reset

Power-cycle (or press EN) rapidly before the 3-second boot window expires. The reset counter accumulates across rapid reboots:

| Cycles | Effect |
|--------|--------|
| 5 – 9  | Clears hostname, auth, and MQTT config; restarts into normal Wi-Fi |
| 10+    | Clears all of the above **plus** stored Wi-Fi credentials; restarts into captive portal |

Serial output shows the accumulated count:

```
[BOOT] reset count 3
[BOOT] reset count 4
...
[BOOT] reset count 5, triggering factory reset
[BOOT] factory reset triggered (clearWifi=0)!
[BOOT] factory reset complete, restarting...
```

---

## Web UI

Browse to the device address to open the configuration page.

### Logo

Place a `logo.png` in the `data/` directory and upload the filesystem image once. The logo appears in the top-left of the configuration page. The `data/logo.png` included in this repo is a 200×200 px transparent PNG.

### Info panel

Shows the current hostname and IP address.

### Hostname

Sets the mDNS name (`<hostname>.local`). Changing the hostname automatically restarts the device so mDNS re-registers with the new name.

### Security

| Field | Description |
|-------|-------------|
| Require password | Enables HTTP Basic Auth on the web UI |
| Password | Password for the `admin` account. Leave blank to keep the existing password |

### MQTT

| Field | Description |
|-------|-------------|
| Enable | Toggle MQTT on/off |
| Broker | Hostname or IP of your MQTT broker |
| Port | Default `1883` |
| User / Pass | Broker credentials (leave Pass blank to keep the existing value) |
| Prefix | Topic prefix (default `device`) |

Click **Save** to persist all settings. Click **Reset Device** to restart the device immediately.

---

## MQTT / Home Assistant

### Connection behaviour

On connect the device publishes `online` to `<prefix>/status` (retained) and sets `offline` as the LWT. If the broker is unreachable, the firmware probes the TCP port before attempting a full MQTT connect and retries every 30 seconds without blocking the web server.

### Extending with discovery and topics

Three stubs in `main.cpp` are the intended extension points:

| Function | Purpose |
|----------|---------|
| `mqttSubscribe()` | Subscribe to command topics after connecting |
| `mqttCallback()` | Handle incoming messages |
| `mqttPublishDiscovery()` | Publish Home Assistant discovery payloads |

---

## HTTP API

| Method | Path | Description |
|--------|------|-------------|
| `GET` | `/` | HTML configuration page |
| `GET` | `/logo.png` | Logo image served from LittleFS |
| `POST` | `/config` | Save configuration; redirects to `/`. Restarts if hostname changed |
| `POST` | `/reset` | Restart the device immediately |

---

## Configuration reference

Config is stored as JSON in LittleFS at `/config.json`.

```json
{
  "hostname": "esp32-device",
  "mqtt": {
    "en": true,
    "host": "192.168.1.10",
    "port": 1883,
    "user": "ha",
    "pass": "secret",
    "prefix": "device"
  },
  "auth": {
    "en": true,
    "pass": "secret"
  }
}
```

The file is written by the web UI. To erase everything including flash, use `pio run --target erase`.

---

## Extending the framework

1. Add your hardware setup in `setup()` after the framework initialises.
2. Add your per-loop logic in `loop()` alongside `server.handleClient()` and `mqttLoop()`.
3. Fill in the three MQTT stubs to subscribe, receive, and publish discovery payloads.
4. Add extra web routes with `server.on(...)` in `startServer()` if you need device-specific endpoints.
5. Persist extra config fields by adding keys to `loadConfig()` and `saveConfig()`.
6. Place static files (images, etc.) in `data/` and upload the filesystem image with `pio run --target uploadfs`.