Ready for synching test

.gitignore

@@ -0,0 +1,5 @@
+# Gitignore settings for ESPHome
+# This is an example and may include too much for your use-case.
+# You can modify this file to suit your needs.
+/.esphome/
+/secrets.yaml

ades-office-resistive-control-panel.yaml

@@ -1,89 +1,17 @@
-substitutions:
-  device_name: "ades-office-control-panel"
-  friendly_name: Ade's Office Control Panel
-
 esphome:
-  name: $device_name
+  name: adesoffice_resistive_control
-  friendly_name: $friendly_name
+  friendly_name: Ade's office Resistive control panel
-  on_boot:
-    - delay: 2s
 
 esp32:
   board: esp32dev
   framework:
     type: arduino
+
 logger:
 
-ota:
-  platform: esphome
-  password: !secret ota_password
-
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-  fast_connect: true
-  on_connect:
-    - lvgl.widget.show: wifiStatusIcon
-  on_disconnect:
-    - lvgl.widget.hide: wifiStatusIcon
-
-
-light:
-  - platform: monochromatic
-    output: backlight_pwm
-    name: Display Backlight
-    id: backlight
-    restore_mode: ALWAYS_ON
-
-time:
-  - platform: homeassistant
-    id: esptime
-
-spi:
-  - id: tft
-    clk_pin: GPIO14
-    mosi_pin: GPIO13
-    miso_pin: GPIO12
-
-i2c:
-  sda: GPIO33
-  scl: GPIO32
-
-touchscreen:
-  platform: cst816
-  id: my_touchscreen
-  display: mainDisplay
-  reset_pin: GPIO25
-  update_interval: 50ms
-  transform:
-    mirror_x: true
-    mirror_y: true
-  on_touch:
-  - lambda: |-
-        ESP_LOGI("cal", "x=%d, y=%d, x_raw=%d, y_raw=%0d",
-            touch.x,
-            touch.y,
-            touch.x_raw,
-            touch.y_raw
-            );
-  on_release:
-    then:
-      - if:
-          condition: lvgl.is_paused
-          then:
-            - logger.log: "LVGL resuming"
-            - lvgl.resume:
-            - lvgl.widget.redraw:
-      - light.turn_on: backlight
-
-output:
-  - platform: ledc
-    pin: GPIO27
-    id: backlight_pwm
-
 api:
   encryption:
-    key: "FdLcYGMsxFkCFoY8UUu0q/huDesKrcy4+vNQujhbXVE="
+    key: "yDySAAGJIQIgZcDURBrLtWiVYNteCm155yyZUnrMjZY="
   on_client_connected:
     - lvgl.widget.show: haStatusIcon
   on_client_disconnected:
@@ -95,10 +23,151 @@ api:
       else:
         - lvgl.widget.hide: haStatusIcon
           
+
+ota:
+  - platform: esphome
+    password: !secret ota_password
+
+wifi:
+  ssid: !secret wifi_ssid
+  password: !secret wifi_password
+  on_connect:
+    - lvgl.widget.show: wifiStatusIcon
+  on_disconnect:
+    - lvgl.widget.hide: wifiStatusIcon
+
+i2c:
+  sda: 27
+  scl: 22
+  scan: true
+
+spi:
+  - id: tft
+    clk_pin: 14
+    mosi_pin: 13
+    miso_pin:
+      number: 12
+      ignore_strapping_warning: true
+  - id: touch
+    clk_pin: 25
+    mosi_pin: 32
+    miso_pin: 39
+
+output:
+  - id: backlightPwm
+    platform: ledc
+    pin: 21
+  - id: outputRed
+    platform: ledc
+    pin: 4
+    inverted: true
+  - id: outputGreen
+    platform: ledc
+    pin: 16
+    inverted: true
+  - id: outputBlue
+    platform: ledc
+    pin: 17
+    inverted: true
+
+light:
+  - id: backlight
+    platform: monochromatic
+    output: backlightPwm
+    name: "Display Backlight"
+    restore_mode: ALWAYS_ON
+  - id: rgbLed
+    platform: rgb
+    red: outputRed
+    green: outputGreen
+    blue: outputBlue
+    name: "RGB LED"
+    restore_mode: ALWAYS_OFF
+
+sensor:
+  - platform: adc
+    pin: 34
+    name: "Brightness"
+    update_interval: 60s
+    id: lsr
+  - platform: homeassistant
+    entity_id: sensor.k1max_progress
+    id: sensor_3dprinter_percentage
+    on_value: 
+      then:
+        - lvgl.label.update:
+            id: lbl_3dprinter_percentage
+            text:
+              format: "Percentage: %.0f%%"
+              args: [x]
+  - platform: homeassistant
+    entity_id: sensor.k1max_extruder_temperature
+    id: sensor_3dprinter_nozzle
+    on_value: 
+      then:
+        - lvgl.indicator.update:
+            id: gauge_3dprinter_nozzle_needle
+            value: !lambda return x;
+        - lvgl.label.update:
+            id: gauge_3dprinter_nozzle_text
+            text:
+              format: "%.0f°C"
+              args: [ 'x' ]
+  - platform: homeassistant
+    entity_id: sensor.k1max_bed_temperature_2
+    id: sensor_3dprinter_bed
+    on_value: 
+      then:
+        - lvgl.indicator.update:
+            id: gauge_3dprinter_bed_needle
+            value: !lambda return x;
+        - lvgl.label.update:
+            id: gauge_3dprinter_bed_text
+            text:
+              format: "%.0f°C"
+              args: [ 'x' ]
+
+text_sensor:
+  - platform: homeassistant
+    entity_id: sensor.k1max_current_print_state
+    id: printerStatus
+    on_value:
+      then:
+        - if:
+            condition:
+              lambda: 'return x == "printing";'
+            then:
+              - lvgl.widget.update:
+                  id: button3dPrinter
+                  state:
+                    disabled: ON
+            else:
+              - lvgl.widget.update:
+                  id: button3dPrinter
+                  state:
+                    disabled: OFF
+        - lvgl.label.update:
+            id: lbl_3dprinter_status
+            text: 
+              format: "Status: %s"
+              args: [x.c_str()]
+  - platform: homeassistant
+    entity_id: sensor.k1max_filename
+    id: printer_modelname
+    on_value: 
+      then:
+        - lvgl.label.update:
+            id: lbl_3dprinter_modelname
+            text:
+              format: "Model: %s"
+              args: [x.c_str()]
+
+
+
 display:
   - id: mainDisplay
     platform: ili9xxx
-    model: ili9341
+    model: ILI9341
     spi_id: tft
     cs_pin:
       number: 15
@@ -109,15 +178,8 @@ display:
     invert_colors: false
     update_interval: never
     auto_clear_enabled: false
-    pixel_mode: 16bit
     transform:
       mirror_y: true
-      mirror_x: true
-      swap_xy: false
-    dimensions:
-      height: 320
-      width: 240
-    color_order: rgb
     init_sequence:
       - [0x01 ]
       - [0xcf, 0x00, 0xC1, 0x30 ]
@@ -142,119 +204,31 @@ display:
       - [0x11 ]  # SLPOUT Exit sleep
       - [0x29 ]  # DISPLAY_ON
 
-sensor:
+touchscreen:
-  - platform: adc
+  platform: xpt2046
-    pin: 34
+  id: mainTouchscreen
-    name: "Brightness"
+  spi_id: touch
-    update_interval: 60s
+  cs_pin: 33
-    id: lsr
+  interrupt_pin: 36
-  - platform: homeassistant
+  threshold: 800
-    entity_id: sensor.k2plus_c06b_print_progress
+  calibration:
-    id: sensor_3dprinter_percentage
+    x_min: 410
-    on_value: 
+    x_max: 3349
-      then:
+    y_min: 179
-        - lvgl.label.update:
+    y_max: 3958
-            id: lbl_3dprinter_percentage
+  on_release:
-            text:
-              format: "Percentage: %.0f%%"
-              args: [x]
-  - platform: homeassistant
-    entity_id: sensor.k2plus_c06b_nozzle_temperature
-    id: sensor_3dprinter_nozzle
-    on_value: 
-      then:
-        - lvgl.indicator.update:
-            id: gauge_3dprinter_nozzle_needle
-            value: !lambda return x;
-        - lvgl.label.update:
-            id: gauge_3dprinter_nozzle_text
-            text:
-              format: "%.0fC"
-              args: [ 'x' ]
-  - platform: homeassistant
-    entity_id: number.k2plus_c06b_nozzle_target
-    id: number_3dprinter_nozzle_target
-    on_value: 
-      then:
-        - lvgl.arc.update:
-            id: arc_nozzle_target
-            value: !lambda return x;
-  - platform: homeassistant
-    entity_id: sensor.k2plus_c06b_bed_temperature
-    id: sensor_3dprinter_bed
-    on_value: 
-      then:
-        - lvgl.indicator.update:
-            id: gauge_3dprinter_bed_needle
-            value: !lambda return x;
-        - lvgl.label.update:
-            id: gauge_3dprinter_bed_text
-            text:
-              format: "%.0fC"
-              args: [ 'x' ]
-  - platform: homeassistant
-    entity_id: number.k2plus_c06b_bed_target
-    id: number_3dprinter_bed_target
-    on_value: 
-      then:
-        - lvgl.arc.update:
-            id: arc_bed_target
-            value: !lambda return x;
-
-text_sensor:
-  - platform: homeassistant
-    entity_id: sensor.k2plus_c06b_print_status
-    id: printerStatus
-    on_value:
     then:
       - if:
-            condition:
+          condition: lvgl.is_paused
-              lambda: 'return x == "printing";'
           then:
-              - lvgl.widget.update:
+            - logger.log: "LVGL resuming"
-                  id: button3dPrinter
+            - lvgl.resume:
-                  state:
+            - lvgl.widget.redraw:
-                    disabled: ON
+      - light.turn_on: backlight
-            else:
+  transform:
-              - lvgl.widget.update:
+    mirror_x: false
-                  id: button3dPrinter
+    mirror_y: true
-                  state:
+
-                    disabled: OFF
-        - lvgl.label.update:
-            id: lbl_3dprinter_status
-            text: 
-              format: "Status: %s"
-              args: [x.c_str()]
-  - platform: homeassistant
-    entity_id: sensor.k2plus_c06b_current_object
-    id: printer_modelname
-    on_value: 
-      then:
-        - lvgl.label.update:
-            id: lbl_3dprinter_modelname
-            text:
-              format: "Model: %s"
-              args: [x.c_str()]
-  - platform: homeassistant
-    entity_id: sensor.k2plus_c06b_working_layer
-    id: printer_working_layer
-    on_value: 
-      then:
-        - lvgl.label.update:
-            id: lbl_3dprinter_layer
-            text:
-              format: "Layer: %s"
-              args: [x.c_str()]
-  - platform: homeassistant
-    entity_id: sensor.k2plus_c06b_print_time_left
-    id: printer_print_time_left
-    on_value: 
-      then:
-        - lvgl.label.update:
-            id: lbl_3dprinter_print_time_left
-            text:
-              format: "Time remaining: %s"
-              args: [x.c_str()]
 number:
   - platform: template
     name: "LVGL Screen Timeout"
@@ -601,24 +575,6 @@ lvgl:
             id: lbl_3dprinter_modelname
             width: 240
             text: "Model: None"
-        - label:
-            align_to:
-              id: lbl_3dprinter_modelname  
-              align: OUT_BOTTOM_LEFT
-              y: 3
-            long_mode: scroll 
-            id: lbl_3dprinter_layer
-            width: 240
-            text: "Layer: 0 of 0"
-        - label:
-            align_to:
-              id: lbl_3dprinter_layer  
-              align: OUT_BOTTOM_LEFT
-              y: 3
-            long_mode: scroll 
-            id: lbl_3dprinter_print_time_left
-            width: 240
-            text: "Print time left: NaN"
         - meter:
             id: meter_3dprinter_nozzle
             align: BOTTOM_LEFT
@@ -637,6 +593,12 @@ lvgl:
                       width: 2
                       color: 0xFF0000
                       r_mod: -4
+                  - tick_style:
+                      start_value: 0
+                      end_value: 380
+                      color_start: 0x0000bd
+                      color_end: 0xbd0000
+                      width: 1
               - range_from: 0 # scale for the value labels
                 range_to: 380
                 angle_range: 240
@@ -656,7 +618,7 @@ lvgl:
             widgets:
               - label:
                   id: gauge_3dprinter_nozzle_text
-                  text: "-.-C"
+                  text: "-.-°C"
                   align_to:
                     id: meter_3dprinter_nozzle
                     align: CENTER
@@ -667,30 +629,6 @@ lvgl:
                     id: meter_3dprinter_nozzle
                     align: CENTER
                     y: 45
-        - arc:
-            align: BOTTOM_LEFT
-            y: -35
-            x: 5
-            height: 110
-            width: 110
-            id: arc_nozzle_target
-            value: !lambda "return id(number_3dprinter_nozzle_target).state;"
-            min_value: 0
-            max_value: 380
-            adjustable: true
-            start_angle: 150
-            end_angle: 30
-            knob:
-              pad_all: 0
-            arc_rounded: false
-            arc_width: 6
-            on_value:
-              then:
-                - homeassistant.service:
-                    service: number.set_value
-                    data:
-                      entity_id: number.k2plus_c06b_nozzle_target
-                      value: !lambda "return x;"
         - meter:
             id: meter_3dprinter_bed
             align: BOTTOM_LEFT
@@ -709,6 +647,12 @@ lvgl:
                       width: 2
                       color: 0xFF0000
                       r_mod: -4
+                  - tick_style:
+                      start_value: 0
+                      end_value: 130
+                      color_start: 0x0000bd
+                      color_end: 0xbd0000
+                      width: 1
               - range_from: 0 # scale for the value labels
                 range_to: 130
                 angle_range: 240
@@ -728,7 +672,7 @@ lvgl:
             widgets:
               - label:
                   id: gauge_3dprinter_bed_text
-                  text: "-.-C"
+                  text: "-.-°C"
                   align_to:
                     id: meter_3dprinter_bed
                     align: CENTER
@@ -739,30 +683,6 @@ lvgl:
                     id: meter_3dprinter_bed
                     align: CENTER
                     y: 45
-        - arc:
-            align: BOTTOM_LEFT
-            y: -35
-            x: 125
-            height: 110
-            width: 110
-            id: arc_bed_target
-            value: !lambda "return id(number_3dprinter_bed_target).state;"
-            min_value: 0
-            max_value: 130
-            adjustable: true
-            start_angle: 150
-            end_angle: 30
-            knob:
-              pad_all: 0
-            arc_rounded: false
-            arc_width: 6
-            on_value:
-              then:
-                - homeassistant.service:
-                    service: number.set_value
-                    data:
-                      entity_id: number.k2plus_c06b_bed_target
-                      value: !lambda "return x;"
 
 
   on_idle:
@@ -871,4 +791,3 @@ switch:
           id: buttonScreens
           state:
             checked: OFF
-

ns-panel-ground-floor.yaml

@@ -0,0 +1,45 @@
+substitutions:
+  # Settings - Editable values
+  device_name: ns-panel-ground-floor 
+  wifi_ssid: !secret wifi_ssid
+  wifi_password: !secret wifi_password
+  nextion_update_url: "http://192.168.17.44:8123/local/nspanel_eu.tft"  # Optional for `esp-idf` framework
+  # Add-on configuration (if needed)
+  # heater_relay: "1"  # Possible values: "1" or "2"
+
+api:
+  encryption:
+    key: "DVkkntEil08ex4e7xjnKTz4o2z/ZM/UHnkjOJP7KUfA="
+# Customization area
+##### My customization - Start #####
+##### My customization - End #####
+
+# Core and optional configurations
+packages:
+  remote_package:
+    url: https://github.com/Blackymas/NSPanel_HA_Blueprint
+    ref: main
+    files:
+      - nspanel_esphome.yaml # Core package
+      # Optional advanced and add-on configurations
+      # - advanced/esphome/nspanel_esphome_advanced.yaml
+      # - nspanel_esphome_addon_climate_cool.yaml
+      # - nspanel_esphome_addon_climate_heat.yaml
+      # - nspanel_esphome_addon_climate_dual.yaml
+    refresh: 300s
+
+esp32:
+  framework:
+    type: esp-idf
+
+time:
+  - id: !extend time_provider
+    timezone: "Europe/Berlin"
+
+wifi:
+  networks:
+    - id: !extend wifi_default
+      manual_ip:
+        static_ip: 192.168.17.139
+        gateway: 192.168.17.1
+        subnet: 255.255.255.0

oekoboiler-interface.yaml

@@ -0,0 +1,634 @@
+esphome:
+  name: oekoboiler-interface
+  friendly_name: Oekoboiler-Interface
+
+esp8266:
+  board: nodemcuv2
+
+
+# Enable logging
+logger:
+  baud_rate: 0
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: !secret oekoboiler_encryptionkey
+  reboot_timeout: 0s      
+
+ota:
+  - platform: esphome
+    password: !secret oekoboiler_otapassword
+
+wifi:
+  ssid: !secret wifi_ssid
+  password: !secret wifi_password
+  power_save_mode: none  # Disable power saving
+  fast_connect: true     # Skip scanning, connect faster
+  reboot_timeout: 0s     # Disable auto-reboot on wifi loss
+ 
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Oekoboiler-Interface"
+    password: !secret oekoboiler_fallbackpassword
+
+captive_portal:
+
+#web_server:
+#  port: 80
+
+# UART configuration for Modbus (0-based register addressing)
+uart:
+  id: mod_bus
+  tx_pin: GPIO1  # D10/TX
+  rx_pin: GPIO3  # D9/RX
+  baud_rate: 9600
+  stop_bits: 1
+  data_bits: 8
+  parity: NONE
+
+# Modbus RTU
+modbus:
+  flow_control_pin: GPIO5  # D1 - DE/RE pin for MAX485
+  id: modbus1
+  send_wait_time: 200ms
+
+modbus_controller:
+  - id: oekoboiler
+    address: 0x1
+    modbus_id: modbus1
+    setup_priority: -10
+    update_interval: 10s
+    command_throttle: 200ms
+
+sensor:
+  # WiFi Signal
+  - platform: wifi_signal
+    name: "WiFi Signal"
+    update_interval: 60s
+
+  # Uptime
+  - platform: uptime
+    name: "Uptime"
+    update_interval: 60s
+
+  # ========================================
+  # INPUT REGISTERS (3x) - Documentation address MINUS 1
+  # ========================================
+  
+  # A1 - Water Temperature (30001 -> 0)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Water Temperature"
+    address: 0
+    register_type: read
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    state_class: measurement
+    accuracy_decimals: 1
+    filters:
+      - multiply: 0.1
+    
+  # A2 - Evaporator Temperature (30002 -> 1)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Evaporator Temperature"
+    address: 1
+    register_type: read
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    state_class: measurement
+    accuracy_decimals: 1
+    filters:
+      - multiply: 0.1
+    
+  # A4 - Ambient Temperature (30003 -> 2)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Ambient Temperature"
+    address: 2
+    register_type: read
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    state_class: measurement
+    accuracy_decimals: 1
+    filters:
+      - multiply: 0.1
+    
+  # A3 - Exhaust Temperature (30004 -> 3)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Exhaust Temperature"
+    address: 3
+    register_type: read
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    state_class: measurement
+    accuracy_decimals: 1
+    filters:
+      - multiply: 0.1
+    
+  # A9 - Return Gas Temperature (30005 -> 4)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Return Gas Temperature"
+    address: 4
+    register_type: read
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    state_class: measurement
+    accuracy_decimals: 1
+    filters:
+      - multiply: 0.1
+
+  # ========================================
+  # HOLDING REGISTERS (4x) - Read-only values
+  # ========================================
+  
+  # Controller Status (41102 -> 1101)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Controller Status Raw"
+    id: controller_status_raw
+    address: 1101
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+  
+  # Operating Mode (41105 -> 1104)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Mode Raw"
+    id: mode_raw
+    address: 1104
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+  
+  # Econ Mode Time Window (41106 -> 1105)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Econ Mode Time Window"
+    address: 1105
+    register_type: holding
+    value_type: U_WORD
+    skip_updates: 4
+  
+  # Alarm sensors (41121-41133 -> 1120-1132)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A1 Sensor"
+    address: 1120
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a1
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A2 Sensor"
+    address: 1121
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a2
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A3 Sensor"
+    address: 1122
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a3
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A6 Sensor"
+    address: 1125
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a6
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A5 High Pressure"
+    address: 1126
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a5
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A4 Sensor"
+    address: 1127
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a4
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Water Temp Warning 55C"
+    address: 1128
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_water_temp
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A9 Sensor"
+    address: 1129
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a9
+
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Alarm A8 Condensate"
+    address: 1130
+    register_type: holding
+    value_type: U_WORD
+    internal: true
+    id: alarm_a8
+
+binary_sensor:
+  - platform: status
+    name: "Connection Status"
+
+  # ========================================
+  # COILS (0x) - Documentation address MINUS 1
+  # ========================================
+  
+  # Compressor (00001 -> 0)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Compressor Running"
+    address: 1
+    register_type: coil
+    device_class: running
+  
+  # Heating Element (00002 -> 1)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Heating Element"
+    address: 2
+    register_type: coil
+    device_class: heat
+  
+    # Fan (00004 -> 3)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Four-Way Valve"
+    address: 3
+    register_type: coil
+    device_class: running
+
+  # Fan (00004 -> 3)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Fan Running"
+    address: 4
+    register_type: coil
+    device_class: running
+  
+  # ========================================
+  # DISCRETE INPUTS (1x) - Documentation address MINUS 1
+  # ========================================
+  
+
+  # Template binary sensors for alarms
+  - platform: template
+    name: "Alarm: A1 Water Temp Sensor"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a1).state != 0;
+
+  - platform: template
+    name: "Alarm: A2 Evaporator Sensor"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a2).state != 0;
+
+  - platform: template
+    name: "Alarm: A3 Ambient Sensor"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a3).state != 0;
+
+  - platform: template
+    name: "Alarm: A6 Heating Element"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a6).state != 0;
+
+  - platform: template
+    name: "Alarm: A5 High Pressure"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a5).state != 0;
+
+  - platform: template
+    name: "Alarm: A4 Exhaust Sensor"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a4).state != 0;
+
+  - platform: template
+    name: "Warning: Water Temperature 55°C"
+    device_class: problem
+    lambda: |-
+      return id(alarm_water_temp).state != 0;
+
+  - platform: template
+    name: "Alarm: A9 Return Gas Sensor"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a9).state != 0;
+
+  - platform: template
+    name: "Alarm: A8 Condensate Overflow"
+    device_class: problem
+    lambda: |-
+      return id(alarm_a8).state != 0;
+
+text_sensor:
+  - platform: template
+    name: "Controller Status"
+    lambda: |-
+      int status = (int)id(controller_status_raw).state;
+      switch(status) {
+        case 0: return {"Power Off"};
+        case 1: return {"Standby"};
+        case 2: return {"Preheating"};
+        case 3: return {"Heating"};
+        case 4: return {"Before Defrost"};
+        case 5: return {"Defrosting"};
+        case 6: return {"After Defrost"};
+        case 8: return {"Alarm"};
+        default: return {"Unknown (" + to_string(status) + ")"};
+      }
+  
+  - platform: template
+    name: "Operating Mode"
+    lambda: |-
+      int mode = (int)id(mode_raw).state;
+      switch(mode) {
+        case 0: return {"Econ Mode"};
+        case 1: return {"Auto Mode"};
+        case 2: return {"Heater Mode"};
+        default: return {"Unknown (" + to_string(mode) + ")"};
+      }
+
+switch:
+  # ========================================
+  # WRITABLE HOLDING REGISTERS - Switches
+  # ========================================
+  
+  # PV Mode (40067 -> 66)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "PV Mode"
+    address: 66
+    register_type: holding
+    bitmask: 1
+    entity_category: config
+    icon: "mdi:solar-power"
+
+  # Heating Element Enable (40015 -> 14)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Heating Element Enable"
+    address: 14
+    register_type: holding
+    bitmask: 1
+    entity_category: config
+    icon: "mdi:heating-coil"
+
+  # Heating Element for Sterilization (40017 -> 16)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Sterilization Enable"
+    address: 16
+    register_type: holding
+    bitmask: 1
+    entity_category: config
+    icon: "mdi:bacteria"
+
+  # Heating Element in Econ Mode (40028 -> 27)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Heating Element in Econ Mode"
+    address: 27
+    register_type: holding
+    bitmask: 1
+    entity_category: config
+
+  # Heat Pump in Heater Mode (40029 -> 28)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Heat Pump in Heater Mode"
+    address: 28
+    register_type: holding
+    bitmask: 1
+    entity_category: config
+
+  # Save Status on Power Off (40061 -> 60)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Save Status on Power Off"
+    address: 60
+    register_type: holding
+    bitmask: 1
+    entity_category: config
+
+  # Electronic Anode (40068 -> 67)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Electronic Anode"
+    address: 67
+    register_type: holding
+    bitmask: 1
+    entity_category: config
+
+number:
+  # ========================================
+  # WRITABLE HOLDING REGISTERS - Numbers
+  # ========================================
+  
+  # Set Temperature PV (40009 -> 8)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Target Temperature (PV Mode)"
+    address: 8
+    value_type: U_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: 5
+    max_value: 70
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+    icon: "mdi:solar-power"
+  
+  # Set Temperature Normal (40010 -> 9)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Target Temperature (Normal)"
+    address: 9
+    value_type: U_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: 5
+    max_value: 70
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Set Temperature F62=0 (40011 -> 10)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Target Temperature (F62=0)"
+    address: 10
+    value_type: U_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: 5
+    max_value: 70
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Temperature Delta/Hysteresis (40012 -> 11)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Temperature Hysteresis"
+    address: 11
+    value_type: U_WORD
+    unit_of_measurement: "°C"
+    min_value: 1
+    max_value: 20
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+    icon: "mdi:thermometer-lines"
+  
+  # Ambient Temperature Shutdown (40013 -> 12)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Heat Pump Shutdown Temperature"
+    address: 12
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: -10
+    max_value: 5
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Maximum Temperature with Heat Pump (40014 -> 13)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Max Temperature Heat Pump"
+    address: 13
+    value_type: U_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: 20
+    max_value: 60
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Ambient Temperature for Heating Element Start (40016 -> 15)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Heating Element Start Temperature"
+    address: 15
+    value_type: U_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: 10
+    max_value: 20
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Sterilization Cycle (40018 -> 17)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Sterilization Cycle Hours"
+    address: 17
+    value_type: U_WORD
+    unit_of_measurement: "h"
+    min_value: 1
+    max_value: 990
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+    icon: "mdi:bacteria"
+  
+  # A1 Temperature Sensor Offset (40019 -> 18)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "A1 Sensor Offset"
+    address: 18
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: -5
+    max_value: 5
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Compressor Delay (40021 -> 20)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Compressor Delay"
+    address: 20
+    value_type: U_WORD
+    unit_of_measurement: "min"
+    min_value: 0
+    max_value: 10
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Defrost Start Temperature (40031 -> 30)
+  - platform: modbus_controller
+    modbus_controller_id: oekoboiler
+    name: "Defrost Start Temperature"
+    address: 30
+    value_type: S_WORD
+    unit_of_measurement: "°C"
+    device_class: temperature
+    min_value: -20
+    max_value: 20
+    step: 1
+    mode: box
+    use_write_multiple: true
+    entity_category: config
+  
+  # Defrost End Temperature (40032

old-phone-doorbell.yaml

@@ -148,4 +148,3 @@ script:
 
 logger:
   level: DEBUG
-

powermeter.yaml

@@ -0,0 +1,77 @@
+esphome:
+  name: powermeter
+  friendly_name: PowerMeter
+
+esp8266:
+  board: esp01_1m
+
+# Enable logging
+logger:
+
+web_server:
+  port: 80
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: "sRMMr/ojhCUtZukAFSRT/fZpvI0bcTPHAqs0CzXY/q0="
+
+ota:
+  - platform: esphome
+    password: "8383401f9c2ff3b99a166c2782307e8b"
+
+wifi:
+  ssid: !secret wifi_ssid
+  password: !secret wifi_password
+  manual_ip:
+    static_ip: 192.168.20.152
+    gateway: 192.168.20.1
+    subnet: 255.255.255.0
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Powermeter Fallback Hotspot"
+    password: "kmSJk2j8Lpak"
+
+captive_portal:
+  
+sensor:
+  - platform: pulse_meter
+    name: 'Power'
+    id: sensor_pulse_meter # Optional ID, necessary if you want to calculate the total daily energy
+    unit_of_measurement: 'W'
+    device_class: power
+    state_class: measurement
+    accuracy_decimals: 0
+    internal_filter: 100ms
+    pin: 
+      number: 12
+      inverted: true
+      mode:
+        input: true
+        pullup: true
+    filters:
+      - multiply: 60
+    total:
+      name: "Electricity Total"
+      unit_of_measurement: "kWh"
+      device_class: energy
+      state_class: total_increasing
+      accuracy_decimals: 3
+      filters:
+        - multiply: 0.001
+  - platform: total_daily_energy
+    name: 'Total Daily Energy'
+    id: sensor_total_daily_energy
+    power_id: sensor_pulse_meter
+    unit_of_measurement: 'kWh'
+    state_class: total_increasing
+    device_class: energy
+    accuracy_decimals: 3
+    filters:
+      # Multiplication factor from W to kW is 0.001
+      - multiply: 0.001
+
+time:
+  - platform: homeassistant
+    id: homeassistant_time